XLPE Insulation Low Smoke Halogen Free Shipboard Symmetric Telecommunication Cable
XLPE insulation low smoke halogen free shipboard symmetric telecommunication cable
Q/XYT 17.3-2009 (Chinese standard) Shipboard power, control and instrument loop cables.
Part 4: Shipboard control cables for rated voltage 0.15/0.25kV
IEC60092-376 shipboard control cables.
(1) The allowed long-duration maximum working temperature of cable conductor is 90°C.
(2) The laying temperature of cable shall not be less than 0°C.
(3) The recommended allowed bending radius shall be:
For Metal braided armoured cable: 6 times value of the outer diameter.
For non-armoured cable with outer diameter exceeding25mm: 6 times value of the outer diameter.
For non-armoured cable with outer diameter below 25 mm: 4 times of the outer diameter
3.Lifting and Storage of Cable
(1) During conveying, the cable and cable drum shall not be damaged and do not push the cable drum directly from the truck. The cable drum shall not be conveyed or stored flat.
(2) Please don’t throw the cable drum or cable ring with cable winded from high space. During conveying, the cable drum must be put stable and fixed using suitable method to prevent from mutual collision or falling over.
(3) Before conveying or rolling the cable drum, it must be fixed and cable whereon must be winded tightly. When rolling, follow the arrowhead on the cable drum or cable winding direction.
(4) During storage the cable drum, package and label shall be complete, and the end capping shall be tight. Once any defect is found, immediately dispose of it. In the area where the cable is stored, no water log is allowed.
4. Installation and laying of cables
(1) When laying, tension should be uniform to avoid twist of the cable. If the cable is twisted, insulation core may be cracked and twisted which consequently causes accident.
(2) When preparing the cable head, strictly follow state codes regarding power construction to use specialized tools.
(3) When installing, once any mechanical damage of the cable is found, please do conduct relevant checks for the cable to see whether the cable insulation is damaged subject to conditions.
(4) Before the laying, checks shall be conducted according to following requirements:
a) Model: specification and voltage of the cable shall be consistent with the design.
b) The cable exterior shall have no damage and have good insulation, and the cable shall be tested and proven qualified.
c) Length of each cable shall be calculated according to design and actual route, reasonably arrange each tray of cable to reduce cable joints.
d) Cable installation in charged area, should have security arrangements.
Model,description and application
|CKEPJ||SC||Copper core EPR insulator no halogen low smoke flame retardant shipboard control cable with thermosetting sheath|
|CKEPJ86||SC||Copper core EPR insulator copper wire braided and armoured no halogen low smoke flame retardant shipboard control cable with thermoplastic sheath|
|CKEPJ96||SC||Copper core EPR insulator steel wire braided and armoured no halogen low smoke flame retardant shipboard control cable with thermoplastic sheath|
|CKJPJ||SC/NSC||Copper core XLPE insulator no halogen low smoke flame retardant shipboard control cable with thermosetting sheath|
|CKJPJ85||SC/NSC||Copper core XLPE insulator copper wire braided and armoured no halogen low smoke flame retardant shipboard control cable with thermosetting sheath|
|CKJPJ95||SC/NSC||Copper core XLPE insulator steel wire braided and armoured no halogen low smoke flame retardant shipboard control cable with thermosetting sheath|
|CKJPF||SC/NSC||Copper core XLPE insulator no halogen low smoke flame retardant shipboard control cable with thermoplastic sheath|
|CKJPF86||SC/NSC||Copper core XLPE insulator copper wire braided and armoured no halogen low smoke flame retardant shipboard control cable with thermoplastic sheath|
|CKJPF96||SC/NSC||Copper core XLPE insulator steel wire braided and armoured no halogen low smoke flame retardant shipboard control cable with thermoplastic sheath|
|Nominal cross section mm2||DC resistance of conductor at 20°C(≤Ω/km)|
|Category 2 copper conductor||Category 5 coppper conductor|
Hebei Huatong wires&cables Group Co.,ltd.It was established in 1993.
Hebei Huatong Wires and Cables Group Co., Ltd covers an area more than 220,000 square meters, owning more than 420 sets manufacturing equipment and more than 250 sets of testing equipment or apparatus. Our annual production capacity is 3 billionYuan.Now there are more than 900 employers in our company, among which more than 150 are technicians. Our products are widely used in the field of electric power, coal, metallurgy, petrochemical industry, railway, national defense, construction, aviation and other national key projects.
We are top cable manufacture of rubber serious cables . Besides these,our submersible oil pump cable and shipboard cable are very influential in domestic, and, the traditional cables are also produced such as PVC power cables, XLPE power cables, ABC cables, wires, control cables, screened cables,communication cables, conductors.We are OEM for many USA, Europen, Australia cable company,70% of our products are exported, most customers are from developed countries. We got ISO,UL,TUV,KEMA,CE and many other certifications.
1.24 years production experience and 14 years export experience .
2.Products certification :UL,CE,BV,TUV,KEMA,PSB,SABS,ABS,NK,LR,KR,GL etc
3.OEM service available based on official & legal authorization.
4.Strict quality control system.
5.Rapid delivery and feedback Faster lead time than our competitors.
6.Excellent quality with reasonable price.
7.Strong technical support (technical data, drawing, etc.)
8.Professional teamwork service for you actively.
9.Stock available, Free sample is available.
1).When can I get the price?
We usually quote within 6 hours after we get your inquiry. If you are very urgent to get the price, please call us or tell us in your e-mail so that we will regard your inquiry priority.
2).How can I get a sample to check your quality?
After price confirmation, you can require for samples to check our quality. Sample is free, but thefreight charge should be paid.
3).How long can I expect to get the sample?
After you pay the freight charge and send us confirmed files, the samples will be ready for delivery in 3-7 days. The samples will be sent to you via express and arrive in 3~5 days. You can use your own express account orprepay us if you do not have an account.
4).What about the lead time for mass production?
Honestly, it depends on the order quantity and the season you place the order.The best record we keep is delivering 10 kilometers cable within a week. Generally speaking, we suggest that you start inquirytwo months before the date you would like to get the products at your country.
5).How to contact us ?
Rita Cheng(Project manager)
Hebei Huatong Wires and Cables Group Co.,Ltd
Add: Huatong Avenue,Fengnan Industrial Development Zone,Tangshan,Hebei,China
Tel: 0086-371-86080580, Cell: 0086-15981926746
- Next: XLPE Solar Overhead Cable with High Quality
- Previous: 0.6/1kv Metal Wire Braid Shipboard Cable
Similar Or Related
- No related articles